|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
DATA SHEET GaAs INTEGRATED CIRCUIT PG2157T5F 50 TERMINATION TYPE HIGH POWER SPDT SWITCH FOR WiMAX DESCRIPTION The PG2157T5F is a GaAs MMIC 50 loss and high isolation. This device is housed in a 12-pin plastic QFN (Quad Flat Non-leaded) package. This package is suitable for highdensity surface mounting. termination type high power SPDT (Single Pole Double Throw) switch which was developed for WiMAX. This device can operate from frequency 2.3 to 5.85 GHz, with low insertion FEATURES * Control voltage * Low insertion loss : Vcont (H) = 2.5 to 3.3 V (3.0 V TYP.) : Vcont (L) = 0 to 0.4 V (0 V TYP.) : Lins1 = 0.60 dB TYP. @ f = 2.3 to 2.7 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : Lins2 = 0.60 dB TYP. @ f = 3.3 to 3.8 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : Lins3 = 0.80 dB TYP. @ f = 5.15 to 5.85 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V * High isolation : ISL1 = 28 dB TYP. @ f = 2.3 to 2.7 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : ISL2 = 25 dB TYP. @ f = 3.3 to 3.8 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V * Handling power : ISL3 = 22 dB TYP. @ f = 5.15 to 5.85 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : Pin (1 dB) +37.0 dBm TYP. @ f = 2.5 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : Pin (1 dB) +37.0 dBm TYP. @ f = 5.85 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V 3.0 0.75 mm) * High-density surface mounting : 12-pin plastic QFN package (3.0 APPLICATIONS * Antenna switch for WiMAX, 802.11a/b/g access point ORDERING INFORMATION Part Number PG2157T5F-E2 Order Number PG2157T5F-E2-A Package 12-pin plastic QFN (Pb-Free) Marking 2157 Supplying Form Embossed tape 8 mm wide Pin 1 indicates roll-in direction of tape Qty 3 kpcs/reel Remark To order evaluation samples, contact your nearby sales office. Part number for sample order: PG2157T5F-A Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge. The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Document No. PG10641EJ01V0DS (1st edition) Date Published October 2006 NS CP(K) PG2157T5F PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM Pin No. 1 Pin Name GND INPUT GND GND Vcont2 GND OUTPUT2 GND OUTPUT1 GND Vcont1 GND (Top View) 12 11 10 (Top View) 12 11 10 50 9 8 7 1 2 3 50 9 8 7 9 8 7 (Bottom View) 10 11 12 2 3 4 5 2157 4 5 6 Vcont1 High Low Parameter Parameter 1 2 3 1 2 3 6 7 8 4 5 6 6 5 4 9 10 11 12 Remark Exposed pad : GND TRUTH TABLE Vcont2 Low High INPUT OUTPUT1 ON OFF INPUT OUTPUT2 OFF ON ABSOLUTE MAXIMUM RATINGS (TA = +25 C, unless otherwise specified) Symbol Vcont Pin TA Tstg Ratings +6.0 +38 45 to +85 55 to +150 Unit V dBm C C Switch Control Voltage Input Power Operating Ambient Temperature Storage Temperature RECOMMENDED OPERATING RANGE (TA = +25 C, unless otherwise specified) Symbol fopt1 fopt2 fopt3 Switch Control Voltage (H) Switch Control Voltage (L) Vcont (H) Vcont (L) MIN. 2.3 3.3 5.15 2.5 0 3.0 0 TYP. MAX. 2.7 3.8 5.85 3.3 0.4 Unit GHz GHz GHz V V Operating Frequency 2 Data Sheet PG10641EJ01V0DS PG2157T5F ELECTRICAL CHARACTERISTICS (TA = +25 C, Vcont (H) = 3.0 V, Vcont specified) Parameter Insertion Loss 1 Insertion Loss 2 Insertion Loss 3 Isolation 1 (INPUT OFF Port) Isolation 2 (INPUT OFF Port) Isolation 3 (INPUT OFF Port) Isolation 4 (OUTPUT1 OUTPUT2) Isolation 5 (OUTPUT1 OUTPUT2) Isolation 6 (OUTPUT1 OUTPUT2) Input Return Loss 1 Input Return Loss 2 Input Return Loss 3 Output Return Loss 1 Output Return Loss 2 Output Return Loss 3 Return Loss (OFF Port) Symbol Lins1 Lins2 Lins3 ISL1 ISL2 ISL3 ISL4 ISL5 ISL6 RLin1 RLin2 RLin3 RLout1 RLout2 RLout3 RL (L) = 0 V, DC blocking capacitors = 8 pF, unless otherwise Test Conditions f = 2.3 to 2.7 GHz f = 3.3 to 3.8 GHz f = 5.15 to 5.85 GHz f = 2. 3 t o 2.7 GHz f = 3. 3 t o 3.8 GHz f = 5.15 to 5.85 GHz f = 2.3 to 2.7 GHz f = 3.3 to 3.8 GHz f = 5.15 to 5.85 GHz f = 2.3 to 2.7 GHz f = 3.3 to 3.8 GHz f = 5.15 to 5.85 GHz f = 2.3 to 2.7 GHz f = 3.3 to 3.8 GHz f = 5.15 to 5.85 GHz f = 2.3 to 2.7 GHz f = 3.3 to 3.8 GHz f = 5.15 to 5.85 GHz MIN. TYP. 0.60 0.60 0.80 MAX. 0.85 0.85 1.05 Unit dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dBm dBm 25 22 19 23 20 18 28 25 22 26 23 21 20 20 20 20 20 20 15 15 15 +37.0 +37.0 20 30 1 dB Loss Compression Input Power Note Pin (1 dB) f = 2.5 GHz f = 5.85 GHz Switch Control Current Switch Control Speed Icont tSW 50% CTL to 90/10% RF A ns 100 Note Pin (1 dB) is measured the input power level when the insertion loss increases more 1 dB than that of linear range. Data Sheet PG10641EJ01V0DS 3 PG2157T5F EVALUATION CIRCUIT Vcont1 1 000 pF 12 50 1 11 10 8 pF 9 OUTPUT1 INPUT 8 pF 2 50 3 8 7 8 pF 4 5 6 OUTPUT2 1 000 pF Vcont2 The application circuits and their parameters are for reference only and are not intended for use in actual design-ins. 4 Data Sheet PG10641EJ01V0DS PG2157T5F MOUNTING PAD LAYOUT DIMENSIONS 12-PIN PLASTIC QFN (UNIT: mm) 0.65 1.0 0.5 0.65 1.0 0.5 0.65 1.0 0.5 0.65 1.0 0.5 12-0.3 1.55 Remark The mounting pad layouts in this document are for reference only. 1.55 Data Sheet PG10641EJ01V0DS 5 PG2157T5F PACKAGE DIMENSIONS 12-PIN PLASTIC QFN (UNIT: mm) 3.00.1 0.750.1 3.00.1 (Bottom View) 1.0 0.50.06 0.40.1 0.9 0.4 0.50.06 1.550.1 1.0 0.24+0.07 -0.05 0.40.1 1.550.1 0.40.1 Dimensions of pin No.1 indication 0.40.1 6 Data Sheet PG10641EJ01V0DS 0.9 0.4 PG2157T5F RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions. methods and conditions other than those recommended below, contact your nearby sales office. Soldering Method Infrared Reflow S o l d e r i n g C on di t io n s Peak temperature (package surface temperature) Time at peak temperature Time at temperature of 220 C or higher Preheating time at 120 to 180 C Maximum number of reflow processes Maximum chlorine content of rosin flux (% mass) Wave Soldering Peak temperature (molten solder temperature) : 260 C or below : 10 seconds or less : 60 seconds or less : 120 30 seconds : 3 times : 0.2%(Wt.) or below : 260 C or below WS260 Co ndi ti on Sym bo l IR260 For soldering Time at peak temperature : 10 seconds or less Preheating temperature (package surface temperature) : 120 C or below Maximum number of flow processes Maximum chlorine content of rosin flux (% mass) Partial Heating Peak temperature (terminal temperature) Soldering time (per side of device) Maximum chlorine content of rosin flux (% mass) : 1 time : 0.2%(Wt.) or below : 350 C or below : 3 seconds or less : 0.2%(Wt.) or below HS350 Caution Do not use different soldering methods together (except for partial heating). Data Sheet PG10641EJ01V0DS 7 4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix -A indicates that the device is Pb-free. The -AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL's understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Lead (Pb) Mercury Cadmium Hexavalent Chromium PBB PBDE Concentration Limit per RoHS (values are not yet fixed) < 1000 PPM < 1000 PPM < 100 PPM < 1000 PPM < 1000 PPM < 1000 PPM Concentration contained in CEL devices -A Not Detected Not Detected Not Detected Not Detected Not Detected Not Detected -AZ (*) If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL's liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability. |
Price & Availability of UPG2157T5F |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |